Finally, you can see the AP Driving Licence Test Slot availability on your screen. AP Learners Driving License Application Correction Online. If you have applied for AP LLR and you want to do some correction, then you have to follow the below procedure for that: Firstly, you have to visit the official website of the ePragathi Portal. Driving Test Slot Booking: 17th,May 2009 (Sunday) LLR Test Slot Booking: 17th,May 2009 (Sunday) Status of Registration Numbers: 4th,March 2009 (Wednesday) Licence Search: 4th,March 2009 (Wednesday) Registration Search: 4th,March 2009 (Wednesday) Web Editable Forms available: 4th,March 2009 (Wednesday) Citizen Charter: 4th,March.
Learner Driving Licence test Slot Booking: Adilabad, Hyderabad, karimnagar, khammam, Mahboobnagar, Medak,Nalgonda, Nizamabad, Ranga Reddy, Warangal, Kodad, Suryapet, Uppal, Khairatabad and Other Location In Telangana State.
The drive against people without valid licence and punishment for the violation has made bike riders without valid driving licence rush to Regional Transport Authority (RTA) offices to apply for one.
On any normal day before the drive was taken up, about half the 1,200 slots for tests to be taken by applicants at various RTA offices in the city used to be booked. But, on Thursday, a day after the checks, 900 slots were booked.
Driving Licence test Slot Booking
Telangana LLR Test Slot Booking, LLR SLOT BOOK, Welcome To TRANSPORT | Telangana Learner Licence On-line Appointment |TS RTA Online Time Slot Booking Online registered citizens are able to give their permanent driving license test. In the slot booking system TS citizens.
Telangana Learner Licence On-line Appointment Online, TS RTA Online Time Slot Booking
Need for a Driving Licence
No person shall drive a motor vehicle in any public place unless he holds an effective driving licence issued to him by the Licensing Authority, authorising him to drive the vehicle.
Licensing Authorities
The Joint Commissioner/ Deputy Commissioner and the Regional Transport Officers are the Licensing Authorities. The Administrative Officers and Motor Vehicle Inspectors are the Additional Licensing Authorities.
Age limit to obtain Driving Licence
- An applicant who has completed sixteen years of age is eligible to apply for a driving licence to drive a motor cycle with engine capacity below 55 cc subject to the condition that the parent or guardian should furnish a declaration in the manner prescribed.
- The applicant who has completed the age of eighteen years of age is eligible to apply for a driving licence to drive a motor vehicle other than a transport vehicle.
- An applicant who has completed twenty years of age will be eligible for applying for a licence to drive a transport vehicle.
Related Posts:
This post explains some of the not so well-known features and configurations settings of the Azure App Service deployment slots. These can be used to modify the swap logic as well as to improve the application availability during and after the swap. Here is what you can do with them:
Swap based on the status code
During the swap operation the site in the staging slot is warmed up by making an HTTP request to its root directory. More detailed explanation of that process is available at How to warm up Azure Web App during deployment slots swap. By default the swap will proceed as long as the site responds with any status code. However, if you prefer the swap to not proceed if the application fails to warm up then you can configure it by using these app settings:
WEBSITE_SWAP_WARMUP_PING_PATH: The path to make the warm up request to. Set this to a URL path that begins with a slash as the value. For example, “/warmup.php”. The default value is /.WEBSITE_SWAP_WARMUP_PING_STATUSES:Expected HTTP response codes for the warm-up operation. Set this to a comma-separated list of HTTP status codes. For example: “200,202” . If the returned status code is not in the list, the swap operation will not complete. By default, all response codes are valid.
You can mark those two app setting as “Slot Settings” which would make them remain with the slot during the swap. Or you can have them as “non-sticky” settings meaning that they would move with the site as it gets swapped between slots.
Minimize random cold starts
Ap Llr Slot Booking Change
In some cases after the swap the web app in the production slot may restart later without any action taken by the app owner. This usually happens when the underlying storage infrastructure of Azure App Service undergoes some changes. When that happens the application will restart on all VMs at the same time which may result in a cold start and a high latency of the HTTP requests. While you cannot control the underlying storage events you can minimize the effect they have on your app in the production slot. Set this app setting on every slot of the app:
Ap Transport Llr Slot Change
WEBSITE_ADD_SITENAME_BINDINGS_IN_APPHOST_CONFIG: setting this to “1” will prevent web app’s worker process and app domain from recycling when the App Service’s storage infrastructure gets reconfigured.
The only side effect this setting has is that it may cause problems when used with some Windows Communication Foundation (WCF) application. If you app does not use WCF then there is no downside of using this setting.
Control SLOT-sticky configuration
Originally when deployment slots functionality was released it did not properly handle some of the common site configuration settings during swap. For example if you configured IP restrictions on the production slot but did not configure that on the staging slot and then performed the swap you would have had the production slot without any IP restrictions configuration, while the staging slot had the IP restrictions enabled. That did not make much sense so the product team has fixed that. Now the following settings always remain with the slot:
- IP Restrictions
- Always On
- Protocol settings (Https Only, TLS version, client certificates)
- Diagnostic Log settings
- CORS
If however for any reason you need to revert to the old behavior of swapping these settings then you can add the app setting WEBSITE_OVERRIDE_PRESERVE_DEFAULT_STICKY_SLOT_SETTINGS to every slot of the app and set its value to “0” or “false”.
swap Diagnostics detector
If a swap operation did not complete successfully for any reason you can use the diagnostics detector to see what has happened during the swap operation and what caused it to fail. To get to it use the “Diagnose and solve problems” link in the portal:
From there click on “Check Swap Operations” which will open a page showing all the swaps performed on the webapp and their results. It will include possible root causes for the failures and recommendations on how to fix them.